If you don't connect your iPod
your mixing desk with the right
cable, you'll lose half your sound!
You may think that
when you buy an iPod, all you need to do is load it with a bunch
of backing tracks and simply plug it in to your PA system and
you're all set and ready to go...
Well, actually that's quite correct
- it really is that simple to connect an iPod to a PA system,
but you would be surprised how many people write to me every week
who have done this but find that they get either a very poor sound
quality and/or low volume levels, and they can't figure out what
they've done wrong!
The wrong way...
Nine times out of ten, the mistake that I find singers make when
connecting an iPod to their PA/mixing desk, is that they use the
wrong type of cable and/or only use ONE channel on their mixing
desk (usually they've tried to take a jack out of the iPod in
to one spare channel of their mixer). Remember, the iPod is stereo
so needs TWO inputs on your mixing desk.
I often hear of singers (wrongly) using a single jack to jack
cable (usually with a 3.5mm jack at one end and a quarter inch/6.3mm
at the other). This is NOT the correct cabling for connecting
your iPod to your PA/Mixing desk!
Just think about it for a moment...when you buy an iPod it comes
shipped with a set of earphones which consist of of ONE 3.5mm
jack going to TWO earbuds. So, this means that the iPod is designed
so that ONE jack takes the audio signal out of the
iPod, but this signal goes in to TWO places (ie
your left and right ears). So, if you want to connect the iPod
to your PA/mixing desk, you need to apply the same cabling configuration
- ie use two input channels on your mixer. The mini-jack/earphone
output of the iPod is stereo which means it sends out both Left
and Right channels (which is why you have two earphones of course)!
So, as you can imagine, if you connect a cable which has only
one jack at the mixer end and is plugged in to one input channel
of your mixing desk, you will only get a partial sound (ie only
one side of the iPods output).
Even if the jack you use at the mixer end is a stereo jack, the
input channel on your desk is mono, so you will still only get
half the sound. It's worth noting that even if your desk is mono
and/or you run your amplifiers or PA in mono, you still need to
use TWO inputs of your desk for the iPod because the issue is
not one of whether you work in stereo or mono - the issue is that
stereo actually simply means two channels (Left & Right),
and in order for you to hear the FULL sound of any stereo device
you connect, you need to feed a Left and Right signal to it, regardless
of whether your PA system is set up in mono or stereo.
The correct way...
To feed the FULL sound from your iPod in to your PA/mixing desk,
you need a stereo cable which has a stereo mini-jack (3.5mm) at
one end, and TWO 1/4" (6.3mm) jacks at the other end. You
could also use a cable which has a stereo mini-jack (3.5mm) at
one end and two XLR jacks at the other end if your mixing desk
uses XLR connections. Both cables will do the same job - just
pick whichever cable suits your mixing desk inputs.
By connecting your iPod in this way, the full signal (Left &
Right) will come out of the 3.5mm jack in your iPod and the two
jacks at the other end (XLR or 6.3mm) will feed both those Left
& Right signals in to two channels of your mixing desk - resulting
in a full sound with nothing missing.
If you are using the proper cable and have correctly connected
your iPod to your mixing desk, you should now have a perfect sound
and no more problems. However, if you are still experience sound
problems (and don't know what's to blame), I've devised a fairly
simple test which should help you troubleshoot your system.
Even if you don't have any problems and you are quite happy
that your cable, iPod and PA are all working just fine, I still
recommend you run this simple test - it'll only take you a couple
of minutes (and you may just discover that not all is as well
as you thought)!
The test uses a process of elimination to troubleshoot the problem,
and goes through each possible problem area step by step, so make
sure you complete the test in the proper sequence using the steps
Step 1: Download the mp3 audio
test file (right click and "save target as..")
and then transfer it in to your iPod, just in the same way you
would download and transfer any other mp3 backing track file to
your iPod. The audio test file contains a voice speaking
the words "left channel" and "right channel".
When the voice says "left channel", you should hear
it coming out of the left channel ONLY. When the voice says "right
channel", you should hear it coming out of the right channel
Step 2: Check that your iPod is putting out the correct audio
signals by connecting earphones/headphones to your iPod and "playing"
the audio test file. Do you hear the "left channel"
and "right channel" spoken audio coming through the
left and then right sides of your earphones? If the answer is
"yes", then you have now established that your iPod
is working properly and is correctly giving out proper left and
right audio signals. Now move on to step 3.
Step 3: Plug your microphone in to the first channel of your mixer/PA
that you intend using for your iPod and speak in to it to check
that the channel is accepting sound and producing audio. Now plug
your microphone in to the second channel that you intend using
for your iPod and speak in to it to check that this channel is
also accepting sound and producing audio. If you can hear yourself
talking through your microphone when it's connected to each channel,
then congratulations, you've now estabished that your mixer/PA
is accepting audio signals on the two channels you've earmarked
for the iPod and you can move on to step 4.
Step 4: Connect your iPod, via the cable, to the two channels
of the mixer you just tested in step 3. Remember, you may need
to adjust (ie reduce) the gain/trim control before connecting
the iPod because the input level of the iPod will probably be
much stronger than the input level of the microphone you used
to test these channels - you don't want to end up with a distorted
sound! Now play the audio test file from the iPod. You
should clearly hear the spoken words "left channel"
and "right channel" coming out of your PA speakers.
If you are running your PA in mono, the "left channel"
and "right channel" spoken words will obviously come
out both your PA speakers and if you are running your PA in stereo,
you will hear the "left channel" and "right channel"
spoken words come out of their respective, seperate speakers.
If the above test fails at step 1, you haven't downloaded the
audio test file properly or transferred it to your iPod properly.
If the test fails at step 2, your iPod or earphones are faulty.
If the test fails at step 3, your microphone or one or both channels
of your mixing desk are faulty.
If the test fails at step 4, then your cable is faulty.
Setting the iPod volume
The other thing that singers often write to me about is "low
signals" or "low volume" problem. There is a simple
solution to this...turn up the volume! OK, OK, I know...if
it was that easy, everyone would just do it and wouldn't be writing
to me and asking about it! And the reason many people don't know
how to set the iPod's volume control is because it is kinda "hidden"
(by that I mean that it is does not have a master volume control
in it's settings menu as you would expect). It does have a "volume
limit" control in the "settings" menu (which I
recommend you set to just a little below maximum) but to set the
main volume, you need to have an actual song playing before you
can do this (a bad bit of designing Apple - shame on you)!
So, to adjust the main volume, when a song is playing, turn the
click wheel clockwise and this will increase the volume.
I like to keep this volume level just a little below maximum too.
The reason I suggest this is that this volume setting will give
a fairly high output signal so you don't need so much gain at
your mixing desk (and it also maximises the signal to noise ratio
keeping background noise down and giving a much cleaner signal).
And, while I'm on the subject
of setting the correct gain on your mixing desk, I must stress
very strongly that you MUST make sure that you set the controls
on your mixing desk correctly before you connect the iPod to it,
especially the gain control (sometimes known as the "trim"
control). If you don't know what I'm talking about, then it is
essential that you read my article on setting
volume levels BEFORE you go plugging your iPod in to your
Article Written by Kenny Campbell
(This article cannot be reproduced without express
(all rights reserved)